GideonTech.com Forums

  • September 30, 2020, 03:48:36 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Pages: [1]   Go Down

Author Topic: Water Resiviour  (Read 762 times)

Epox

  • Senior Modder
  • ***
  • Karma: +0/-0
  • Offline Offline
  • Posts: 301
    • http://www.teen-moods.net
Water Resiviour
« on: March 15, 2003, 06:12:34 PM »

Look @ These Pictures of a plexiglass resiviour:

http://desigen.free.fr/mod-genesis/images/wip/68.jpg
http://desigen.free.fr/mod-genesis/images/wip/76.jpg

How can I make my own like that, seal and ready for use?
Tutorials? Examples? Cheap premade ones?

-No I will not BUY a differnt one.
-No I will not make it out of anther material
-No I will not purchase a kit
-No I will no choose anther design

-If you don't have anything POSITIVE to contribute then don't reply.

Thank you.
Logged

morphine

  • Guest
Water Resiviour
« Reply #1 on: March 15, 2003, 06:21:40 PM »

thequark@wanadoo.fr <thequark@wanadoo.fr>
Logged

RentonLovesJunks

  • Elite Modder
  • ****
  • Karma: +0/-0
  • Offline Offline
  • Posts: 2,448
Water Resiviour
« Reply #2 on: March 15, 2003, 06:29:14 PM »

i made my own like that(not exactly but same priniple).

heres what you need:
Plexi, thinkness is up to you, and size, should be enough to complete the whole thing(im not sure about dimentions on this one)+ some extra.
a way to cut it. best way is with a table saw. but since im guessing you dont have one, the only other way to get perfectly straight cuts is to use the scoring method. take a razor knife and make several passes(probably 50 or so)up against a straight edge on desired line, slowly cutting into the material. once over a little more than half way thru, break the piece and it should cut on the line.

then, get some 90 second epoxy from your local hardware store. mix up enuf to do one side of the piece, apply to both surfaces, and mate them, it would be wonderful if you had a 90 degree angle clamp, but its not absolute nessary, just use a framing square or anything else that has a perfect 90 angle.

that should be enuf to get you started. im sure other people will add more.
Logged

Epox

  • Senior Modder
  • ***
  • Karma: +0/-0
  • Offline Offline
  • Posts: 301
    • http://www.teen-moods.net
Water Resiviour
« Reply #3 on: March 15, 2003, 09:15:21 PM »

thanks RentonLovesJunks
So basically I am just gluing this thing together with 90second epoxy?
Logged

NewModder

  • GT Fanatic
  • **
  • Karma: +0/-0
  • Offline Offline
  • Posts: 51
Water Resiviour
« Reply #4 on: March 19, 2003, 04:19:11 PM »

That sounds fun, I think I will give that a try on my next mod.

I just hope I don't glue my hands together!! :embr:  :tool:
Logged

minnick007

  • GT Fanatic
  • **
  • Karma: +0/-0
  • Offline Offline
  • Posts: 114
Water Resiviour
« Reply #5 on: March 19, 2003, 04:34:38 PM »

You can get some added leak protection by using a tube of clear silicone.  Just work it in the creases and let it dry.  It works in a caulk gun.  You can get it at most hardware stores.
Logged
Pages: [1]   Go Up
 

Page created in 0.071 seconds with 34 queries.